The STOP IT® PIPE REPAIR SYSTEM repairs cracks and leaks in Carbon steel, stainless, aluminum, copper, galvanized; PVC, CPVC, PVDF, polyethylene, polypropylene and fiberglass pipes, to name a few. Please visit the rest of our web site to learn more about the STOP IT® PIPE REPAIR SYSTEM and our products
STOP IT® Pipe Repair Tape is a knitted, fiberglass tape coated with special urethane resins that are water-activated.
It is ideal for pipe leak repairs and reinforcing pipe joints in any situation - even under water! This in-field repair system can be quickly applied - one man, no tools, no hot work and it fully cures to a hard, durable repair in 30 minutes. Available in the standard pack or the new money saving bulk pack.
STOP IT HP™ is a leak sealant product designed for applications with working pressures up to 2000 psi.
The introduction of StopIt HP™ allows leak-sealing procedures to be extended to significantly higher pressures than with the original StopIt® formulation or other competing products. Laboratory testing has demonstrated an excellent degree of reproducibility as well as a significant margin of safety with respect to the upper pressure limit.
STOP IT HP™ application entails mixing of a pre-measured two-part sealant, wetting of a fibrous reinforcement tape, and wrapping of the tape on to the pipe surface. Applications can be made regardless of pipe orientation and result in a durable coating approximately 5 mm in thickness with superior pressure sealing capabilities.
STOP IT HP™ surface preparation consists of removing any loose scale and any lubricants or greases. The system should be relieved of all pressure until the product is fully applied and cured. Application surfaces should be dried prior to application and warmed if the pipe surface is less than 50° F or cooled if greater than 100° F
STOP IT HP™ is a multi-component system and as such requires assembly. Following preparation of the area to be treated, the mixing of the sealant requires only seconds and may be immediately applied to the reinforcement tape. The wetted tape possesses a working time of approximately 8-10 minutes. The exact application time will depend on the specific conditions under which StopIt HP™ is being applied.
STOP IT HP™ will exhibit maximum pressure performance when allowed to cure as a complete application for a time period of 24 hours. Operations may be resumed in as little as 4 hours following the completed application, however with less certainty of highest attainable performance. Laboratory testing reflected failure pressures in excess of 5000 psi for more than 90% of samples tested. Test samples entailed 4 plies of the reinforcement tape/sealant composite being applied over 1/8" holes. Applications under field conditions are anticipated to yield variable results due to the nature of the leak site and surface preparation
RiserRescue™ represents the latest technology in the remediation of production riser pipe surfaces. Highly adherent, thick polymeric coatings are field installed in regions spanning the splash and light zones near the water surface. These coatings effectively seal the pipe surface from the marine environment, eliminating corrosion and substantially increasing the lifetime of the riser.
RiserRescue™ technology benefits:
1. Refurbishment of existing risers in-situ, avoiding costly replacement
2. Inhibits corrosion and marine invasion on the coated riser
3. Eliminates need to shut-in production
4. Avoids hot work
5. Will not support combustion
6. Highly cost effective protection
FIX STIX™ Fix anything... FAST! A hand-moldable, steel filled epoxy...stops leaks, fills holes and cracks and can be used as an adhesive. Conformable, safe and simple-to-use. Stops leaks, fill holes and cracks fast. Sets rock hard in 20 minutes in a wide range of temperatures. No hot work, measuring, or special tools required. Ready to use. FIX STIX™ is pre-measured, non-toxic, solvent free, with little odor. It can be used on potable water lines. FIX STIX™ will not shrink, crack or pull away and it has exceptional chemical resistance. Additionally, FIX STIX™ can be machined, threaded and painted after it has fully cured.
FIX STIX™ is a hand moldable, industrial strength, steel impregnated epoxy used to fill either holes or cracks, will bond and repair almost any pipe construction. The product cure is approximately 20 minutes, and the product works underwater and over a wide temperature range.
FUSION TAPE™ - Heavy duty, self-bonding, self-fusing, seamless silicone tape.
Indumar Products - Fusion Tape
FUSION TAPE™ won't crack or separate with sudden shock, vibration, expansion, or contraction. It is not tacky to the touch and requires no heat or tools to promote fusion. This simple to use, all purpose self-fusing tape is an ideal alternative to shrink wrap tubing and vinyl tapes.
FUSION TAPE™ bonds into a permanent, inseparable, cohesive insulator at room temperature. It has a dielectric strength of 400 volts/mil. and works over a wide range of temperatures. It can also be used as a primary cable insulation where Class H temperatures (180 C/356 F) are present. It also resists moisture and ozone making it an excellent environmental insulator.
Emergency Leak Repair Kits
First Response™ Leak Repair Kit
The First Response™ Leak Repair Kit
provides everything in one box for maintenance and safety teams to quickly
respond to most common leaks, cracks, and gashes in pipes, tanks, and drums.
Each kit includes a small, medium, and large
size of the STOP IT® Pipe Repair System, five Fix Stix™
Epoxy, eighteen assorted wooden plugs, rubber hammer, two Plug-N-Dike®
Plug Rugs, three Plug Patties, lead wool filler pack,
hot/cold hose repair tape, and an instructional CD.
UNIVERSAL SERIES – Kits AE and D
Universal
kits are designed to plug hazardous material leaks in any type of low-pressure
vessel. The kits contain everything needed to respond to leaks in tanks and
drums. The wide variety of sealing devices and materials address surface holes
of all shapes, as well as cracks and gashes. All bolts, back-up plates, and
hardware manufactured from 304 stainless steel. Accompanying tools are available
in standard or non-sparking versions.
Kits
'AE' and 'D' contain two toggle-bolt ball plugs, six toggle-bolt
surface plugs, two T-bolt crack patches, five self tapping screw patches, nine
assorted wooden plugs, Fix Stix™ Epoxy, Plug-N-Dike™ Plug Pattie, lead wool
pack, hot/cold hose repair tape, sorbent pad, tubeless tire repair kit, 8"
x 12" solid neoprene and 20" x 20" closed-cell foam gasketing
material, steel drift pin, OSHA approved 200' roll of barricade tape, tools for
installing all patches and heavy duty carrying case.
Kit 'AE' contains items for larger holes, cracks and gashes in
addition to the standard items listed above. These include one 8" x
12" stainless steel plate lined with 3/4" thick soft neoprene material
and three T-bolts with preassembled wingnut washer combos. A second 8" x
12" stainless steel neoprene backed plate is included with hardwood
cribbing ladder patch and two 22' heavy-duty nylon straps.
EXTERNAL PIPE LEAK CONTROL KITS – Kits C-2
and C-3
Pipe
Leak Control Kits are designed to quickly respond to leaks in straight
runs of piping. Simply snap the clamp around the pipe, drop bolt head through
open-slotted lug and tighten nuts. Versatile clamps respond to water,
wastewater, fuel, chemical, air and gas leaks.
Repair clamps are made of corrosion resistant 304 stainless steel, lugs are made
of rugged ductile iron and shop coated for added protection. Bolts are plated
for longer life. Grade 304 rubber compound gasket offers superior resistance to
oils, aromatic and aliphatic hydrocarbons, condensates, gasoline and natural
gas.
All External Pipe Leak Control Kits include extra solid neoprene and closed-cell
foam gasketing material for odd sized, out-of-round, and corroded pipe
applications. Accompanying tools are available in standard or non-sparking
versions. Kits are packaged in a heavy-duty carrying case.
SERIES 'C-2' contains ten assorted clamps for 1/2" through
4" diameter pipe, extra gasketing material and installation tools. Clamp
sizes are 1/2", 3/4", 1", 1 1/4", 1 1/2", 2", 2
1/2", 3", 3 1/2", 4".
SERIES 'C-3' contains three large clamps for 5", 6"
and 8" diameter pipe, extra gasketing material and installation tools.
Clamp sizes are 5", 6" and 8".
PIPE PLUGGER KIT – KIT C-1
The
Pipe Plugger Kit is designed to quickly plug open-ended pipes. Kit
allows you to instantly plug knocked-off pipes carrying water, fuel, chemicals
and gas. Great for knocked-off gas meters and tank truck discharge valves.
1" to 5" sizes have pressure relief vents to help get the plugs seated
under pressure. Pressure relief vents on 1 1/2" through 5" plugs can
connect to enclosed valve and discharge hose. This enables fluid or gas to be
rerouted to another line, discharged to a recovery vessel or flared. The Pipe
Plugger Kit can also be used for drain line cleaning and nitrogen purging
operations.
SERIES 'C-1' contains ten stainless steel pipe plugs, wooden
plug, valve and discharge hose set, all necessary tools for installation and
heavy-duty carrying case. Plug sizes are 3/4", 1", 1 1/4", 1
1/2", 1 3/4", 2", 2 1/2", 3", 4".
A separate 5" 'C-1' plug is also available.
THE ROLL-OVER KIT – Kit F
The
Roll-over Kit is designed to patch a large hole, crack, or gash in a
large vessel or tank. The kit has a patch that conforms to the curvature of the
vessel. The patch uses a variety of T-bolts to support itself directly to the
hole. The leak is then sealed by tightening the compression bolts around the
frame, conforming the patch to the vessel.
Series 'F' contains one 3/4" neoprene gasketed stainless
steel patch measuring 13" x 23". One stainless steel support frame
with compression bolts, three stainless steel T-bolts with preassembled wingnut
washer combos, all necessary tools and heavy-duty carrying case
Universal
kits are designed to plug hazardous material leaks in any type of low-pressure
vessel. The kits contain everything needed to respond to leaks in tanks and
drums. The wide variety of sealing devices and materials address surface holes
of all shapes, as well as cracks and gashes. All bolts, back-up plates, and
hardware manufactured from 304 stainless steel. Accompanying tools are available
in standard or non-sparking versions.
Kits
'AE' and 'D' contain two toggle-bolt ball plugs, six toggle-bolt
surface plugs, two T-bolt crack patches, five self tapping screw patches, nine
assorted wooden plugs, Fix Stix™ Epoxy, Plug-N-Dike™ Plug Pattie, lead wool
pack, hot/cold hose repair tape, sorbent pad, tubeless tire repair kit, 8"
x 12" solid neoprene and 20" x 20" closed-cell foam gasketing
material, steel drift pin, OSHA approved 200' roll of barricade tape, tools for
installing all patches and heavy duty carrying case.
Pipe
Leak Control Kits are designed to quickly respond to leaks in straight
runs of piping. Simply snap the clamp around the pipe, drop bolt head through
open-slotted lug and tighten nuts. Versatile clamps respond to water,
wastewater, fuel, chemical, air and gas leaks.
The
Pipe Plugger Kit is designed to quickly plug open-ended pipes. Kit
allows you to instantly plug knocked-off pipes carrying water, fuel, chemicals
and gas. Great for knocked-off gas meters and tank truck discharge valves.
1" to 5" sizes have pressure relief vents to help get the plugs seated
under pressure. Pressure relief vents on 1 1/2" through 5" plugs can
connect to enclosed valve and discharge hose. This enables fluid or gas to be
rerouted to another line, discharged to a recovery vessel or flared. The Pipe
Plugger Kit can also be used for drain line cleaning and nitrogen purging
operations.
The
Roll-over Kit is designed to patch a large hole, crack, or gash in a
large vessel or tank. The kit has a patch that conforms to the curvature of the
vessel. The patch uses a variety of T-bolts to support itself directly to the
hole. The leak is then sealed by tightening the compression bolts around the
frame, conforming the patch to the vessel.
